Volume 34,Issue 1,2011 Table of Contents

  • Display Type:
  • Text List
  • Abstract List
  • 1  Parameters design of powertrain system of electric vehicle with two-speed gearbox
    QIN Da-tong ZHOU Bao-hua HU Ming-hui HU Jian-jun WANG Xi
    2011, 34(1):1-6. DOI: 10.11835/j.issn.1000-582X.2011.01.001
    [Abstract](2832) [HTML](0) [PDF 7.35 M](2547)
    Abstract:
    A scheme of two-speed transmission is proposed based on an electric vehicle (EV) with a settled gear ratio. A new traction motor is chosen and a two-speed automatic gearbox without clutch is designed, and matching design between the motor and the two-speed gearbox is carried out. In order to improve operation efficiency of the motor, speed ratios of the two-speed gearbox are optimized aiming at lest energy consumption of the motor over the ECE drive cycle under the condition of ensuring the dynamic performance of the EV. A shifting strategy to guarantee high operation efficiency of the motor is drew up. The simulation results indicate that the energy consumption is decreased by 6.6% and the driving range is extended by 7.1% compared with the EV with a settled gear ratio.
    2  Shifting control and simulation of wet dual clutch transmission
    LIU Zhen-jun HAO Hong-wei DONG Xiao-hong LIU Fei
    2011, 34(1):7-14. DOI: 10.11835/j.issn.1000-582X.2011.01.002
    [Abstract](2039) [HTML](0) [PDF 8.86 M](1651)
    Abstract:
    The dynamic model of the shift process of wet dual clutch transmission (DCT) is set up. Aiming at the characteristics of wet dual clutch transmission, such as being highly nonlinear and difficult to establish its math model, etc., a multiple rule weighting factor fuzzy controller is designed. Then the control scheme of shift process is built, which completes the transfer of engine torque through a combination of a manipulation of engine control and clutch pressure. Dynamic simulation model of wet DCT power train is implemented by using Matlab/Simulink software, the control scheme of shift process is simulated based on this dynamic model. The simulation results show that the control scheme can meet the needs of DCT shift process, and the tracking performance of controller is good. Finally, influencing factors of transmission shift control is discussed.
    3  Harmonic wavelet demodulation for gearbox fault diagnosis
    LIU Xiao-feng PENG Yong-jin LI Hui
    2011, 34(1):15-20. DOI: 10.11835/j.issn.1000-582X.2011.01.003
    [Abstract](2138) [HTML](0) [PDF 6.62 M](1354)
    Abstract:
    On the basis of partial decomposition in frequency domain with harmonic wavelet package method and Hilbert demodulation, the demodulation based on harmonic wavelet package transform is introduced. The Fourier spectra analysis is carried out after preprocessing, and the depth of decomposition and frequency band are determined by the analysis of frequency band distribution and the theoretic computation of gear box characteristic frequency. Then with FFT and IFFT the corresponding meshing component is extracted. Finally, the modulation information is extracted via Hilbert envelop analysis approach. With the proposed method, wear and notch faulty gearbox are tested and analyzed by experiment, respectively. The results prove that this method can locate gearbox fault precisely and provide corresponding basis for judging fault cause and degree.
    4  Collision detection for down-load system in large-scale superpower laser facility
    XIE Zhi-jiang LIU Qi-nan YUAN Xiao-dong LI Cheng
    2011, 34(1):21-25. DOI: 10.11835/j.issn.1000-582X.2011.01.004
    [Abstract](1749) [HTML](0) [PDF 5.62 M](1243)
    Abstract:
    The particularity of the assembly and rectification processing of line-replaceable unit (LRU) in large-scale superpower laser facility is analyzed. Oriented bounding box (OBB) of down-load system, which is based on space region partition, is set up, and Minkowski sum is introduced into OBB calculation. Then the separating axis theorem is optimized, and a dynamic OBB hierarchy tree detecting method is created by combining locality principle of collision. The results from the assembly and rectification practice in a large-scale superpower laser facility confirm that the method is highly efficient and reliable.
    5  Vibration characteristics of face-gear transmission system with parametric excitation
    YANG Zhen WANG San-min FAN Ye-sen LIU Hai-xia
    2011, 34(1):26-35. DOI: 10.11835/j.issn.1000-582X.2011.01.005
    [Abstract](1587) [HTML](0) [PDF 16.88 M](2595)
    Abstract:
    In order to study the influences of different factors on nonlinear dynamics of face-gear transmission system, a nonlinear dynamic model is presented. This model includes backlash, general transmission error, time-varying meshing stiffness, meshing damping, bearings and external load, etc. Based on numerical analysis theory of nonlinear dynamics, the equations are solved and the bifurcation characteristics with different parameters are obtained. And the calculation results show that increasing the backlash and time-varying meshing stiffness will augment the dynamic load of system, but increasing the mesh damping will reduce the dynamic load effectively.
    6  A comprehensive evaluation method of fuzzy matter element for CNC equipment quality
    ZHANG Gen-bao PANG Ji-hong CHEN Guo-hua GE Hong-yu
    2011, 34(1):36-41. DOI: 10.11835/j.issn.1000-582X.2011.01.006
    [Abstract](1663) [HTML](0) [PDF 5.36 M](1179)
    Abstract:
    A comprehensive evaluation method based on fuzzy matter element analysis is proposed to solve problems of multiple performance and quality evaluation for computer numerical control (CNC) equipment. The fuzzy matter element theory is utilized to analyze multi-scale quality characteristics and attributes. Then, the comprehensive quality evaluation model for CNC equipment is founded by using fuzzy matter element analysis method. Analytic hierarchy process (AHP) and information entropy are applied to obtain the objective index weights. Furthermore, the combinational weight is calculated with the optimal mathematics model based on the least square method. Finally, the fuzzy matter element method is used to determine the assessment result. The case study indicates that the method has a certain rationality and feasibility.
    7  Illumination compensation of color video for driver fatigue monitor
    ZHU Shu-liang WANG Zeng-cai WANG Bao-ping
    2011, 34(1):42-46. DOI: 10.11835/j.issn.1000-582X.2011.01.007
    [Abstract](2009) [HTML](0) [PDF 5.54 M](1385)
    Abstract:
    A robust method to compensation illumination of driver video color image to enhance image quality has been proposed. Firstly, the original image is decomposed into high-frequency image and low-frequency image based on spatial image decomposition. The illumination information is completely contained in the low-frequency image. Next, low-frequency image is compensated by using Retinex approach which can brighten the darker area. Then, the compensated low-frequency image and high-frequency image are synthesized. Finally, new image is obtained by illumination balance of synthesized image. Results show that the algorithm has better results compared with the traditional algorithm.
    8  Wrinkling limit prediction of rotary-draw bending process for thin-walled rectangular aluminum alloy tube
    LIU Yu-li LI Jia-jia ZHAO Gang-yao YANG He
    2011, 34(1):47-52. DOI: 10.11835/j.issn.1000-582X.2011.01.008
    [Abstract](2159) [HTML](0) [PDF 7.21 M](1027)
    Abstract:
    Wrinkling is one of main forming defects of the rotary-draw bending process for thin-walled rectangular aluminium alloy tube, which severely restricts the improvement of the forming quality and forming limit. Therefore, a regression prediction model of the wrinkling wave height is built based on finite element(FE) simulation combined with orthogonal regression analysis, and its reliability is validated by experiments. Then the analytical model of forming limit without the occurrence of wrinkling is derived. The laws of the core number, the clearance between mandrel and tube and the clearance between wiper die and tube affecting wrinkling limit are obtained, and the wrinkling limit diagram for the rotary-draw process of thin-walled rectangular tube is obtained.This research provides basis and guidance for improving forming quality of the rotary-draw bending process for the rectangular tubes in production.
    9  An optimization method for the nozzle arrangement in secondary cooling zone of continuous casting
    JIN Xing CHEN Deng-fu LONG Mu-jun ZHANG Jian CHEN Man-li
    2011, 34(1):53-59. DOI: 10.11835/j.issn.1000-582X.2011.01.009
    [Abstract](1878) [HTML](0) [PDF 10.37 M](1208)
    Abstract:
    Based on the existing research on nozzle arrangement method in secondary cooling zone of continuous casting, the method of superposed water flow density is put forward to optimize the nozzle arrangement at casting direction and transverse section of slab according to the optimization principle. The two-dimension heat transfer model is established. The solidification morphology of cross-section at casting direction is simulated with consideration of the influence of water flow density inhomogeneity on solidification process at transversal section, and the temperature distribution of slab, solidification process, and quality of slab are compared between before and after optimization. The results indicate that the surface temperature of slab is dropped equably after optimization, and the casting blank is cooling uniformly in the water springing zone so as to ensure better quality of the casting blank.
    10  Quick and direct reduction process of vanadium and titanium iron concentrate with carbon-containing pellets at high temperature
    LIU Song-li BAI Chen-guang HU Tu LV Xue-wei QIU Gui-bao
    2011, 34(1):60-65. DOI: 10.11835/j.issn.1000-582X.2011.01.010
    [Abstract](1782) [HTML](0) [PDF 5.76 M](1250)
    Abstract:
    By using laboratory high temperature experimental furnace, stage reduction test on vanadium and titanium iron concentrate with carbon-containing pellets under experimental conditions of 1 350 ℃ and in nitrogen atmosphere is introduced,and its tissue composition, microstructure is also studied by TG-DTA, XRD, SEM and other testing method. The experimental results show that reduction process on quick reduction of vanadium and titanium iron concentrate of carbon-containing pellets respectively is Fe2TiO4 and Fe3O4, 3(Fe3O4)·Fe2TiO4, Fe3O4·Fe2TiO4, Fe2TiO4 and FeO, Fe and FeTi2O5. In the stage of generating float by magnetite iron reduction, the new phase of Fe2TiO4 is generated, and finally vanadium and titanium iron concentrate is reduced into Fe and (Fe,Mg)Ti2O5.
    11  Effect of B2O3 on the physico-chemical properties of mold slag used for high-Al steel
    YU Xiong WEN Guang-hua TANG Ping WANG Huan
    2011, 34(1):66-71. DOI: 10.11835/j.issn.1000-582X.2011.01.011
    [Abstract](1849) [HTML](0) [PDF 5.67 M](1247)
    Abstract:
    A new mold slag with low content SiO2 and high content Al2O3 is designed in order to avoid or alleviate the reaction between Al and SiO2 during the continuous casting of high-Al steel, the acidity of this slag is adjusted by adding B2O3, and the effect of B2O3 content on the fusion property, viscosity property and heat transfer characteristics through the mold slag film of the mold slag is analyzed. The results show that the fusion temperature, viscosity, viscous flow activation energy decrease and heat flux through the slag film increases with the increase of B2O3 content in the range of 4%~10%; temperature time transformation (TTT) diagrams move to longer incubation time with the increase of B2O3, while the crystallization speed of mold fluxes decreases; under this experiment condition, the precipitation of CaF2 crystals can be restrained by the increase of B2O3 content in the mold slag.
    12  The development of martensitic stainless steel 4Cr10Si2 for durable knives and scissors
    LI Yuan-rui DENG Li-ping HUI Zhi-qiang WANG Shu-zhen
    2011, 34(1):72-76. DOI: 10.11835/j.issn.1000-582X.2011.01.012
    [Abstract](1833) [HTML](0) [PDF 5.91 M](1165)
    Abstract:
    After introducing the development of knife and scissor materials at home and abroad, the chemical composition of 4Cr10Si2 steel is designed according to the steel alloying principle and Schaeffler diagram. Then 4Cr10Si2 steel sheet with the thickness of 6 mm is prepared. After the tests of hardness, microstructure, tensile property and EBSD, etc., heat treatment test of the steel sheet is carried out and the heat treatment parameters of making kitchen knives and scissors are confirmed. Then, after the bending strength and resistance electrochemical corrosion tests by using the samples treated with optimum heat treatment process, the steel is made into kitchen knives. The testing and trial show that 4Cr10Si2 steel has better performance than 4Cr13 except slightly lower Ecorr and Icorr.
    13  Optimization and springback control of ultra-high strength steel anti-collision side beam forming process
    ZHANG Xu ZHOU Jie
    2011, 34(1):77-81. DOI: 10.11835/j.issn.1000-582X.2011.01.013
    [Abstract](1764) [HTML](0) [PDF 5.49 M](1505)
    Abstract:
    The anti-collision side beam inside the car doors is a key component to improve the safety. Foreign automobile companies use ultra-high strength steel plate to manufacture it. However, it is very difficult to form at room temperature, so usually it is made by hot stamping but the cost is high. The use of FEM software Dynaform in simulating and optimizing the forming process at room temperature is described, and the influence of temperature on internal organizational changes of the ultra-high strength sheet is mainly studied. By comparing the simulation result and real sample, the effect of addendum on stamping and springback is researched and convex roofs in the addendum is added to optimize the surface. It is helpful for manufacturing the relative high strength steel parts.
    14  Image reconstruction of electrical impedance tomography based on particle swarm optimization algorithm
    CHEN Min-you YANG Yan-li HE Wei ZHANG Cong-yu LI Bing
    2011, 34(1):82-87. DOI: 10.11835/j.issn.1000-582X.2011.01.014
    [Abstract](1446) [HTML](0) [PDF 5.88 M](1109)
    Abstract:
    Electrical impedance tomography (EIT) has many advantages in practical application,but image reconstruction of EIT is a highly ill-posed, non-linear inverse problem. Newton-Raphson algorithms are widely used in EIT, which have to calculate the Jacobian matrix and use regularization techniques. So this kind of algorithms is complex and less stable. To address the problem, a new static image reconstruction method for EIT is proposed based on particle swarm optimization (PSO) algorithm. PSO is a population-based, adaptive search optimization technique. It is simple in concept, few in parameters, quick in convergence and easy in implementation. The model of EIT forward problem is given and some appropriate improvements in PSO are made to accommodate the solution of EIT. Compared with Newton-Raphson(MNR) algorithms, PSO only uses an iterative processing to get the best solution instead of using a complicated Jacobian matrix. The experimental results indicate that using PSO-based algorithm to solve image reconstruction of EIT, the position of mutation region is more accurate and graphics space resolution is much higher.
    15  The simulation of conducted EMI in the ignition system for automotives
    YU Ji-hui JIA Jin WANG Quan-di LI Xu
    2011, 34(1):88-93. DOI: 10.11835/j.issn.1000-582X.2011.01.015
    [Abstract](1591) [HTML](0) [PDF 7.28 M](1556)
    Abstract:
    The ignition system in automobiles is a main source of electromagnetic interference (EMI), because the electromagnetic emission from the system has the characteristics of high-energy and wide-bandwidth. A method for EMI prediction based on its components’ circuit models is presented. First, the characteristics of the components are analyzed and the equivalent circuits are drew; then, the parasitic parameters of the electromagnetic device are extracted from measurement, analytical solution or finite element method (FEM); and finally, the circuit model of the whole ignition system model in high frequency condition is established. This model is verified by the measurement and simulation results in time domain and in frequency domain.
    16  Surface discharge characteristics and gas generation law inoil-paper insulation of transformer
    CHEN Wei-gen YANG Jian-feng LING Yun CHEN Xi
    2011, 34(1):94-99. DOI: 10.11835/j.issn.1000-582X.2011.01.016
    [Abstract](2366) [HTML](0) [PDF 7.04 M](2170)
    Abstract:
    Based on a surface discharge model, partial discharge experiment in the simulation transformer tank is carried out to research the development characteristics and characteristic parameters’ variation law of surface discharge in transformer oil-paper insulation, and the variation characteristic of dissolved gases in oil in the discharge process is emphatically researched. The results show that the surface discharge value increases at the beginning stage of the discharge process, and reaches its maximum after 2~3 h, then it decreases gradually. As the development of partial discharge, the absolute generation speed of CO fluctuates around a certain value with small variation. While, the absolute generation speeds of H2 and CH4 increase first and then decrease, and the variation of discharge spectrum is highly similar to the variation of oil-dissolved gas’ absolute generation speed.
    17  Dissimilatory iron reduction processes of soil from Three GorgesReservoir area and its effect on chemical form of Fe
    WANG Tu-jin JI Fang-ying HE Qiang YE Jiang-yu LI Si CAO Lin
    2011, 34(1):100-104. DOI: 10.11835/j.issn.1000-582X.2011.01.017
    [Abstract](1764) [HTML](0) [PDF 5.88 M](1286)
    Abstract:
    Purple soil and yellow soil from Three Gorges Reservoir area are submerged and incubated under a nitrogen atmosphere at constant temperature (25℃) to study the dissimilatory iron reduction processes and its effect on chemical form of Fe. The results show that pH and ORP decrease with the transition of soil redox condition, and it is especially obvious for yellow soil. The content of Fe(Ⅱ) increases to 3 495.21 mg/kg for yellow soil and 536.44 mg/kg for purple soil. There are no obvious changes of redox condition and Fe(Ⅱ) for sterile soil. It suggests that dissimilatory iron reduction should be driven by metabolic activity of microbe. With the transition of soil redox condition, the content of oxide-Fe increases significantly, and the content of Fe(Ⅱ) and oxide-Fe are significantly and positively correlated, which indicate that transformation of Fe speciation is the result of dissimilatory iron reduction.
    18  Sedimentation law research and transportationfeasibility study of backfilling slurry
    ZHANG Qin-li XIE Sheng-qing ZHENG Jing-jing WANG Xin-min
    2011, 34(1):105-109. DOI: 10.11835/j.issn.1000-582X.2011.01.018
    [Abstract](1432) [HTML](0) [PDF 5.88 M](1103)
    Abstract:
    Through the analysis of movement forms of backfilling slurry in the pipeline self-flowing transportation system and the sedimentation law of backfilling aggregate granule, it is known that the transportation stability of backfilling slurry is related to transportation speed and the length of horizontal pipeline. Combined with the characteristics of gangue paste-like slurry in Suncun Mine, the pipeline transport process of slurry is simulated by Fluent, which is a well-known fluid analysis software, and also the self-flowing transportation feasibility of paste-like slurry with gangue as main backfilling aggregate is researched in theory. The research shows that the self-flowing pressure can overcome the resistance loss in the way of the transmission pipeline. When the horizontal pipe transmission speed is 3.82 m/s, the vertical pulsating velocity component of slurry (Sv) can reach 38.3 cm/s and the interfering sedimentation speed of gangue (Vgg) is just 0.99 cm/s, it can know that Sv > Vgg. Therefore, paste-like slurry can arrive at the mined-area by self-flowing transportation.
    19  Experiments on influence of slurry kinds on mechanicalbehavior of interface between gravel and concrete
    PENG Kai ZHU Jun-gao WU Xiao-yu ZHANG Dan
    2011, 34(1):110-115. DOI: 10.11835/j.issn.1000-582X.2011.01.019
    [Abstract](2063) [HTML](0) [PDF 6.84 M](1188)
    Abstract:
    The mechanical behavior and mechanism of the interface between structure and coarse grained soil are investigated through simple shear tests on the conditions of bentonite slurry, clay slurry and without slurry, respectively. The results indicate that different kinds of slurry have important influence on shear strength. Compared with the interface without slurry, the shear strength with bentonite slurry reduces by 45% approximately, significantly more than clay slurry which reduces by 10%. The value of the friction angle with bentonite slurry is about 60% of that with clay slurry. Shear displacement increases as upright stress increases when reaches its failure states at the same height, and shear displacement with bentonite slurry is smaller than that with clay slurry when with the same upright stress and height. The upright displacement with bentonite slurry is greater than that with clay slurry under the same upright stress. In addition, shear dilatation is apparent under the low normal stress when without slurry. Otherwise, it appears as shear contraction.
    20  Experiments on flow characteristics in coaxial annular channel heat exchanger with membrane spiral tubes
    ZHAO Zhen-xing YANG Zhen GUO Qin-qin LIU Hong CAO Zi-dong
    2011, 34(1):116-120. DOI: 10.11835/j.issn.1000-582X.2011.01.020
    [Abstract](1512) [HTML](0) [PDF 6.55 M](1537)
    Abstract:
    The coaxial annular channels’ experimental platform is built to study its flow characteristics when S/d0=2.0, S/d0=2.5, S/d0=3.0, and it is compared with circular pipe’s theoretical value. The purpose is to study the influence of flow rate, pressure, flux, heat transfer temperature and geometric parameters on the coaxial annular channels’ flow characteristics of spiral tube heat exchanger. The results show that for the same annulus width and outside diameter of spiral tube, annular channels’ import, export and total resistance coefficients are decreasing and tend to constants gradually as Reynolds number increases; all the resistance coefficients of annular channel’s outer ring are bigger than those of annular channel’s middle ring and inner ring. But the resistance coefficients of annular channel’s middle ring and inner ring are equal; under the same Reynolds number, the smaller the annulus width is, the bigger pressure drop of annular channel is.
    21  Establishment of total ammonia-nitrogen accumulation prediction model in two-phase anaerobic digestion of OFMSW and its verification
    JIA Chuan-xing PENG Xu-ya LIU Guo-tao
    2011, 34(1):121-127. DOI: 10.11835/j.issn.1000-582X.2011.01.021
    [Abstract](2671) [HTML](0) [PDF 8.00 M](1283)
    Abstract:
    Nitrogen transformation characteristic experiments of organic fraction of municipal solid waste (OFMSW) in a batch hydrolysis-UASB two-phase anaerobic digestion are carried out to solve the problems of total ammonia-nitrogen (TAN) accumulation and obtain appropriate key process control parameters. Based on the experiment results, TAN accumulation prediction model in the two-phase anaerobic digestion of OFMSW with digestive effluent reuse is established. And then with the prediction model analyzed, reflux ratio is obtained as a key process control parameter to prevent TAN accumulation. In the end, verification tests are designed to validate the feasibility and practicability of resolving TAN accumulation by controlling reflux ratio. In verifying experiment, when reflux ratio is set at 0.85, TAN concentration of UASB effluent is increased to a constant value, which is 1 900 mg/L. Furthermore, the accumulated TAN has no negative influence on the population and activity of methanogens, on the contrary, it develops the buffer capacity to acid and alkaline and keeps the anaerobic system more steadily. To sum up, a method of resolving the problem of TAN accumulation by controlling reflux ratio of digestive effluent has been ascertained radically, and the method can be used in the preventing of ammonia inhibition in two-phase anaerobic digestion process.
    22  A domain decomposition algorithm in meshless method for discontinuous problem
    LIU Jun YAN Bo JIANG Nai-bin SUN Ying-xue
    2011, 34(1):128-133. DOI: 10.11835/j.issn.1000-582X.2011.01.022
    [Abstract](1360) [HTML](0) [PDF 6.24 M](1157)
    Abstract:
    A domain decomposition algorithm for material and displacement discontinuity problems in meshless method is presented. The domain is decomposed into sub-domains along the discontinuous interface. The continuity of the displacements on the interface is satisfied through the introduction of two transformation matrixes. The partitioned-matrix method is proposed to calculate the transferred stiffness matrix,which is sparse and bandy. By means of coupling meshless method and finite element method, the essential boundary condition can be imposed directly. The computer program based on the presented method is developed and two numerical examples, a beam consisted with two kinds of materials and an edge-cracked plate under uniform tension, are employed to demonstrate the correctness and efficiency of the method.
    23  CFD simulation of droplet formation in a microfluidic T-junction
    DONG Li-chun WU Ji-zhou REN Gui-xiang TAN Shi-yu HUANG Da-fu LI Wen-ping HUANG Shao-jian
    2011, 34(1):134-139. DOI: 10.11835/j.issn.1000-582X.2011.01.023
    [Abstract](1766) [HTML](0) [PDF 6.26 M](1381)
    Abstract:
    Droplet formation in a microfluidic T-junction is simulated by using computational fluid dynamics (CFD) method. The accuracy of CFD study is verified by comparing the simulation result with the experimental results in literatures. It is found that the formation of droplets in the T-junction can be divided into 3 steps: droplet emergence and growing up, separation with the dispersed phase, and detachment from the channel wall. The study on the wetting property of the channel wall shows that it has a remarkable influence on the droplet formation. Only when the contact angle of the dispersed phase on the wall is smaller than 90°, the droplets can be formed. Moreover, the wetting property of the channel significantly affects the detachment time of the droplets from the wall. The effect of the capillary number, Ca, on droplet formation is studied by varying the viscosity, and velocity of the continuous phase or the interfacial tension, respectively. In the range that the droplets can be formed, the droplet size decreases with the increase of Ca,and when Ca is bigger than 0.067, droplet diameter shows an obvious linear relationship with 1/Ca.
    24  Thermal analysis on the kinetics of thermal decomposition of FeS
    ZHAO Sheng-ping JIANG Jun-cheng ZHENG Jie
    2011, 34(1):140-144. DOI: 10.11835/j.issn.1000-582X.2011.01.024
    [Abstract](1875) [HTML](0) [PDF 4.43 M](1143)
    Abstract:
    More and more attention is paid to the spontaneous combustion accidents of oil which is induced by FeS. The thermal analysis experiments of FeS are finished with different heating rates of 2, 5, 8, 10, 15 ℃/min. The essence about the oxidation of ferrous sulfide in air is a process containing physical adsorption, chemical adsorption and chemical reaction of ferrous with the oxygen. Based on the experiments data, the kinetics of thermal decomposition of FeS is studied by model-fitting and model-free methods. It is shown that the computable results of the model-fitting are unstable and irresponsible. The kinetics parameters of FeS are calculated by the iso-conversional method. The apparent activated energy E is equal to(135.81±8.27)kJ/mol. Through the equation of Satava-Sestak, the kinetics of thermal degradation of FeS is researched. The reaction accorded with the Avrami-Erofeev (m=2) kinetic model is g(α)= [-ln(1-α)]1/2. The apparent activated energy E is 148.43 kJ/mol and the apparent preexponential factor A is 3.82×109 K/s.

    Current Issue


    Volume , No.

    Table of Contents

    Archive

    Volume

    Issue

    Most Read

    Most Cited

    Most Downloaded