Volume 35,Issue 11,2012 Table of Contents

  • Display Type:
  • Text List
  • Abstract List
  • 1  Three-dimensional crack propagation simulation and life prediction in tooth root of cylindrical gear
    LIN Tengjiao ZHONG Sheng SHEN Liang
    2012, 35(11):1-7. DOI: 10.11835/j.issn.1000-582X.2012.11.001
    [Abstract](2070) [HTML](0) [PDF 10.24 M](1261)
    Abstract:
    Based on the theory of linear elastic fracture mechanics,a three-dimensional boundary element model of cylindrical gear with crack in tooth root is established and the stress intensity factor of crack tip is calculated. Then,through the automatic propagation analysis of initial crack,the growth trajectory and the propagation life of the crack at tooth root are obtained. Based on the obtained result,the influence of load magnitude,crack size,crack location and crack orientation on the crack propagation life is discussed. The results indicate that the tooth root crack expands slowly at first and then faster and faster;the crack propagates more easily along the tooth width than along the tooth thickness;the crack propagation life decreases with the increase of load magnitude or crack size,the effects of load magnitude on propagation life is significantly and the propagation life is more sensitive to initial crack depth than width;the propagation life is longer when crack is closer to the gear end-face and is shortest when crack has an initial direction about -30 degrees.
    2  Analysis of nonlinear dynamic characteristics of the Schmidt offset coupling
    ZHU Caichao WANG Meng DU Xuesong
    2012, 35(11):8-14. DOI: 10.11835/j.issn.1000-582X.2012.11.002
    [Abstract](2075) [HTML](0) [PDF 8.50 M](1063)
    Abstract:
    Considering the coupling interaction between transverse vibration and torsional vibration of the system,a dynamic analysis model of the Schmidt offset coupling is established by the method of concentrated parameter and the dynamic equation of this system is deduced by the Newton method. Considering the effect of engine and error excitations on the transmission system,the Gill numerical solution method is used to study the dynamic response of the drive system. The results show that it has a good dynamic performance and its vibration belongs to almost periodic vibration,which provides theoretical guidance for further dynamic performance optimization and engineering application.
    3  A method of rotor orbit purification based on ensemble empirical mode decomposition filter
    CHEN Renxiang TANG Baoping Ly Zhongliang
    2012, 35(11):15-20. DOI: 10.11835/j.issn.1000-582X.2012.11.003
    [Abstract](2226) [HTML](0) [PDF 9.11 M](1434)
    Abstract:
    In order to purify rotor orbit,the characteristics of suppressing the phenomenon of mode mixing and filtering in ensemble empirical mode decomposition (EEMD) are studied,and a method of rotor orbit purification is presented. Ensemble empirical mode decomposition decomposes a complicated signal into a collection of intrinsic mode functions (IMFs). Then,according to prior knowledge of rotor system,choose intrinsic mode function components and reconstruct the signal,and,the purification of rotor orbit is obtained. The effectiveness of the method is proved by the successful purification of rotor orbit coming from the test-bed. And,the results of comparing the performances of the proposed method to the harmonic-based and the EMD-based purification of axis orbit method show the advantage of the de-noising method. The method provides a new way for fault diagnosis of rotating machinery.
    4  Exact solid-modeling of double pitch ZN-type worm gears based on meshing theory
    SHU Linsen CAO Huajun XU Lei LI Zhiyong
    2012, 35(11):21-27. DOI: 10.11835/j.issn.1000-582X.2012.11.004
    [Abstract](2157) [HTML](0) [PDF 8.71 M](1287)
    Abstract:
    Exact solid-modeling of worm gears is very important for computer aided analysis,the model precision directly influences the accuracy of the subsequent CAE analysis. Aimed at the problem,a method for exact solid-modeling of double pitch ZN-type worm gears is presented based on meshing theory. Firstly,the paper analyzes the forming principle and characteristics of double pitch ZN-type worm gears and then deduces the mathematical equations of double pitch ZN-type worm gear;secondly,gear tooth working surface and boundary surfaces of worm gears are reconstructed by NURBS surface interpolation;finally,the three dimensional solid model of double pitch ZN-type worm gears is generated by trimming and stitching the surface. Error analysis shows that the geometric error of double pitch ZN-type worm gears established by this method is minimal,and it can meet the requirements of the subsequent CAE analysis,and proposes a new thought for the complex structure design of worm gears.
    5  MPF-MMAC:A novel wireless sensor network MAC protocol
    TANG Baoping RUAN Qidong PEI Yong
    2012, 35(11):28-33. DOI: 10.11835/j.issn.1000-582X.2012.11.005
    [Abstract](2030) [HTML](0) [PDF 7.06 M](1008)
    Abstract:
    A novel cluster expanding and scheduling strategy is put forward,and then a multi-channel medium access control (MAC) protocol is designed for wireless sensor network (WSN) applications that ask for high network throughput and low transmission delay. The proposed MAC protocol based on TDMA can effectively improve throughout and channel utilization with a controllable hybrid channel access method. The protocol is simulated with OMnet++ software and the outcomes show that the protocol has good throughput performance and low delay time.
    6  Experimental study of gear bending fatigue strength under random load according to three-parameter Weibull distribution
    HU Jianjun XU Hongbin GAO Xiaowang ZU Shihua
    2012, 35(11):34-39. DOI: 10.11835/j.issn.1000-582X.2012.11.006
    [Abstract](1937) [HTML](0) [PDF 7.77 M](1336)
    Abstract:
    Random-amplitude fatigue load spectrum for experiments is made according to the ubiquitous three-parameter Weibull distribution in gear transmission. Gear bending fatigue test under the random load is carried out on a MTS electro-hydraulic servo material fatigue tester by using group testing method,and the S-N curve of gear bending strength under three-parameter Weibull distribution with specific variation coefficients is obtained. The fatigue test results show the gear’s endurance life under random load is far less than that under constant load when the load submits to three-parameter Weibull distribution random load spectrum. The theoretical value of fatigue limit for gear under random load is predicated and compared with test results. The theoretical value is in accordance with the test results. Therefore,the fatigue strength of gear bending under random load can be deduced according to the load ratio coefficient of random load spectrum.
    7  Airfoil design using improved particle swarm optimization
    CHEN Jin WANG Quan LI Songlin GUO Xiaofeng
    2012, 35(11):40-46. DOI: 10.11835/j.issn.1000-582X.2012.11.007
    [Abstract](1715) [HTML](0) [PDF 8.64 M](1429)
    Abstract:
    Based on the theory of standard particle swarm optimization (PSO), an improved particle swarm optimization algorithm is presented, and it has a better optimized performance than standard PSO. A multi-objective wind turbine airfoil shape optimization model is established and 4 kinds of different thick wind turbine airfoils with better performance are designed by using the improved PSO algorithm. The aerodynamic performance of the CQU-A18 and CQU-A21 airfoils are analyzed in detail compared with the commonly used wind turbine airfoil with the same thickness. The results show that the new airfoils show very good aerodynamic characteristics, and they are found to be very insensitive to leading edge roughness. The new airfoils exhibit the higher lift coefficient and larger lift/drag ratio in both smooth condition and rough condition at the main angle of attacks. The performances of the new airfoils show a significant improvement compared with the typical airfoils.
    8  Numerical simulation of influence for the process parameters on multi-roll flexible stretch forming
    ZHANG Haohan LI Mingzhe FU Wenzhi CHEN Xue FENG Pengxiao
    2012, 35(11):47-52. DOI: 10.11835/j.issn.1000-582X.2012.11.008
    [Abstract](1616) [HTML](0) [PDF 7.83 M](1072)
    Abstract:
    Multi-roll stretch forming (MRSF) process is a new flexible process. Through extensive numerical simulations of the MRSF process, it is found that the smaller the distance between die and rollers is, the more easily the shape can be formed, and the better the quality of formed part can be. However, the distance between clamps and rollers has little effect on the formed parts. The corresponding stretch forming experiment has been done and the results show that the simulation trend is consistent with the experimental results.
    9  Relationship between porosity and chloride diffusivity in cement-based composite materials
    GAO Lixiong SUN Guowen ZHANG Yunsheng SUN Wei
    2012, 35(11):53-61. DOI: 10.11835/j.issn.1000-582X.2012.11.009
    [Abstract](2679) [HTML](0) [PDF 10.15 M](1818)
    Abstract:
    For investigating the effect of porosity in cement-based composite materials on diffusion coefficient of chloride ion, a series of mortar specimens with different water-cement ratios, different volume fractions and different diameters and graduation of aggregates are cast, and then chloride diffusivity of mortar specimens are measured by steady-state electric acceleration method and pore structure parameters of corresponding samples are obtained by mercury intrusion porosimetry. At the same time, the pore size distributions are visualized by X-ray micro-focus computer tomography. The results show that porous interfacial transition zones between aggregate and bulk cement paste significantly change the distribution of pore structure in hardened cement paste, and the smaller water-cement ratio is, the more significant the effect of interfacial transition zones on pore structures of hardened cement paste is. A good correlation between the total porosity, capillary porosity and the diffusion coefficient of chloride ion in cement-based composite materials has been determined and the continuous pore diameter is linearly related to the diffusion coefficient of those. Furthermore, the larger the continuous pore diameter is, the larger the value of chloride diffusivity is.
    10  Experimental research for heat transfer coefficient of casting/mold interface with thermal-mechanical coupling effects using steady-state method
    ZHAO Jianhua SONG Gang WANG Yajun ZENG Li
    2012, 35(11):62-66. DOI: 10.11835/j.issn.1000-582X.2012.11.010
    [Abstract](1783) [HTML](0) [PDF 6.48 M](1109)
    Abstract:
    The variation tendency of interface heat transfer coefficient of A356/H13 steel with the thermal-mechanical coupling effects is investigated by using an experimental setup designed by the authors. The results show that,the steady-state heat flow method, which is realized by means of a multiple force amplifier consisting of a pulley force amplifier and a hydraulic force amplifier,can enable the study of the heat transfer coefficient of casting/mold interface with thermal-mechanical coupling effects; the bilateral heating experiments are superior to the unilateral ones; the increase of temperature or load causes the increase of interface heat transfer coefficient in the test range; moreover, the interface heat transfer coefficient at high temperature is more sensitive to temperature than at low temperature, the interface heat transfer coefficient of A356/H13 is nearly linear with the interface load.
    11  Kinetics analysis of sinter-reduction base on oxygen blast furnace
    XUE Qingguo LAN Rongzong WANG Jingsong HAN Yihua WANG Lintao
    2012, 35(11):67-74. DOI: 10.11835/j.issn.1000-582X.2012.11.011
    [Abstract](2048) [HTML](0) [PDF 9.83 M](1173)
    Abstract:
    The reduction experiment of sinter has been taken in oxygen blast furnace atmosphere by thermal balance weight loss method. The changes of reduction RI and reduction rate RI′ have been examined, and then kinetics analysis of sinter reduction have been carried on. Results show the reduction of sinter is significantly improving in oxygen blast furnace atmosphere and the reduction RI measures up to 98.2% when the sinter is reducing at 900 ℃. With the reduction temperature increasing, the reduction rate of sinter speeds up significantly, and the end time of reduction is shorten from 117 min at 900 ℃ to 63min at 1 100 ℃. When sinter is reducing in oxygen blast furnace atmosphere,the reductive reaction is mainly controlled by the interface chemical reaction in the beginning, and then turn to hybrid controlled by both interface chemical reaction and internal diffusion about 20 min later. The apparent activation energy of reaction that sinter reducing in oxygen blast furnace atmosphere at 900 ~ 1 100 ℃ is 38.30 kJ/mol.
    12  The harmless process for the sodium removal of Bayer red mud by CO2
    WU Long LI Shiqi SHEN Ping
    2012, 35(11):75-80. DOI: 10.11835/j.issn.1000-582X.2012.11.012
    [Abstract](1711) [HTML](0) [PDF 6.73 M](1124)
    Abstract:
    The harmless process for the sodium removal of red mud is investigated by using CO2 to remove sodium from the aluminum solid waste Bayer red mud. The indicator of the experiment is the sodium removal rate. Reaction temperature, reaction time, solid-liquid ratio, CO2 gas flow, and the particle size of red mud five impact factors for the sodium removal are researched and the results are as follows. The reasonable parameters for the sodium removal are reaction temperature 25 ℃, reaction time 100 min, solid-liquid ratio 1/5, CO2 gas flow 0.8 L/min, and fine grinding red mud particle size. Under the reasonable parameters condition, the sodium removal rate is 76.12%, the remaining Na2O content is 2.5%, and the concentration of NaHCO3 solution is about 4%. Compared with the traditional process, the process is simpler. By the process, the PH value of red mud slurry is decreased to 7.1 from 10.2, and the red mud becomes harmless. During the process, the emission of greenhouse gas CO2 is reduced and NaHCO3 can be recycled, conducive to recycling of resources.
    13  Oxidation capability of modified fly ash based adsorbent for mercury in coal-fired flue gas
    XU Zhipeng LIU Qingcai YAO Chunling YANG Jian WEI Min
    2012, 35(11):81-85. DOI: 10.11835/j.issn.1000-582X.2012.11.013
    [Abstract](1928) [HTML](0) [PDF 5.68 M](1281)
    Abstract:
    Fly ash based adsorbent is dipping modified by NaCl or NaBr solution and the purpose is to improve their oxidation capability. Adsorption experiments of vapor-phase elemental mercury are performed in a laboratory-scale fixed-bed reactor. Physical properties of the adsorbent before and after modification are measured and the influences of the solution concentration and flue gas temperature on mercury oxidation rate are studied. The results show that when NaBr solution concentration is 5%, the mercury oxidation rate can reach 79.43%. The saturation adsorption quantity of absorbent 5%-NaBr is 1 700 ng/g and the service life is about 480 hours. Flue gas temperature played an important role in mercury oxidation and the best temperature ranged from 100 to 200 ℃.
    14  Order planning for iron and steel enterprise considering production organization constraints
    LU Yongming WANG Lina CHEN Hongzhi ZHAO Yongli PAN Qiujuan XUE Xiangrong
    2012, 35(11):86-91. DOI: 10.11835/j.issn.1000-582X.2012.11.014
    [Abstract](1661) [HTML](0) [PDF 7.56 M](1048)
    Abstract:
    To realize efficient operation, the production organization constraints of ironmaking/steelmaking interface, desulphorization basic oxygen furnace and decarburization basic oxygen furnace, refining equipment and casting/rolling interface of typical steel production process A are analyzed. Order planning model of iron and steel enterprises considering production organization constraints is established. The scheduling compact and coordination and the optimization of commissioning date of different production lines are fully considered in the model. Then, the model is solved by tabu search. Finally, three different sizes of actual production contracts which are randomly selected from the steel plant A are simulated. The results prove the presented model and algorithm can harmonize and optimize the production effectively and also realize the process running efficiently.
    15  Automatic quality assessment of fingerprint image
    YANG Yongming ZHANG Zulong HAN Fengling LIN Kunming SUN Hao
    2012, 35(11):92-98. DOI: 10.11835/j.issn.1000-582X.2012.11.015
    [Abstract](1921) [HTML](0) [PDF 9.67 M](1425)
    Abstract:
    Based on multiple influencing factors, a new method of automatic fingerprint image quality evaluation is proposed for improving the success rate of automation fingerprint identification system (AFIS). At first, the original image’s local texture, global texture, available size and dry or wet condition are regarded as quality impact factors, local texture quality score is calculated by local gradient correlation, and then the last three factors’ quality scores are obtained by block computation thought. Then, with different influence weights, the above four impact factors are linked together to assess image quality synthetically. Finally, effect of partial impact factor is adjusted to correct the final quality score. FVC2004DB2_B is used for algorithm testing. The results suggest that this method can reasonably classify fingerprint image into 5 grades and the precision can achieve 97.5%, and that shows the method is helpful to success rate of AFIS.
    16  Analysis on weld metal and element migration of 316L-20G clad pipe
    FAN Zhaoting ZHANG Shengtao YIN Linliang LIU Jia DAI Zhixiang
    2012, 35(11):99-103. DOI: 10.11835/j.issn.1000-582X.2012.11.016
    [Abstract](2061) [HTML](0) [PDF 7.35 M](1377)
    Abstract:
    The proliferation of weld and major alloying elements are studied and analyzed by scanning the EDS element of 316L/20G clad pipe weld joint, 316L substrate and 20G steel, and by scanning the electron microscopy and the energy spectrum analysis of 316L-weld zone and 20G steel-weld zone. The results show that the alloying elements in the weld transition layer are diluted by carbon steel, and the carbon atoms spread to the 316L and weld, while alloying elements in the 316L and wire, such as Cr, Ni, penetrate to the carbon steel, but the transition layer plays a good role in isolation, resulting in 316L stainless steel alloy element content is not significantly reduced, maintaining the 316L base metal resistant to corrosion.
    17  Treatment of wastewater from ABS condensation drying section by BAC-SBR reactor
    YANG Liwei LAI Bo ZHOU Yuexi PANG Cuicui LIAN Yu ZHANG Sheng ZHOU Jihong
    2012, 35(11):104-110. DOI: 10.11835/j.issn.1000-582X.2012.11.017
    [Abstract](2036) [HTML](0) [PDF 8.17 M](1179)
    Abstract:
    Wastewater from ABS condensation drying section is treated by biological activated carbon-sequencing batch reactor (BAC-SBR), and degradation process of the toxic and hazardous pollutants in ABS wastewater is studied significantly by using UV-visible spectrum and Fourier transform infrared spectroscopy (FTIR). The results show that the treatment process of ABS wastewater by BAC-SBR contained three phases of adsorption, bioregeneration and completion. The COD and TOC removal efficiencies of ABS wastewater are both more than 85% after 180 min treatment in BAC-SBR reactor, and the analysis results of UV-vis and FTIR suggest that the toxic and hazardous pollutants i.e., aromatic compounds and organic nitriles in ABS wastewater can be decomposed and transformed efficiently by BAC-SBR reactor.
    18  Dynamic superposition and simulation research on flowing of gas outburst and mine ventilation network
    LI Zongxiang LIU Yu YU Jingxiao JIA Jinzhang
    2012, 35(11):111-116. DOI: 10.11835/j.issn.1000-582X.2012.11.018
    [Abstract](1836) [HTML](0) [PDF 10.57 M](1037)
    Abstract:
    In allusion to the “5·30”especially serious coal and gas outburst accident of Tonghua coal mine of Songzao Coal Electricity Group CO., LTD in 2009, a detailed simulation of the mutation process of mine ventilation system during gas outburst disaster period is done by using theory of ventilation network with sources and numerical simulation technology (we develop a computer simulation system). Three changing processes, namely outburst overflow, natural flow and ventilation downstream occurs in the ventilation system after outburst. Due to the expanded power of outburst source, gas enters main ventilation roadways at first, and flows outward, and flows counter-current along main intake air roadway, and then enters low air quantity roadways with air doors or underground chamber, which leads to gas concentration overrun and threat to the whole mine. After outburst, gas power disappears. Due to the action of gas natural ventilation pressure, mine ventilation may begin to flow naturally. After the ventilation systems are restored, gas flows with the wind as a result of the power of the main fan. Due to the interference of gas natural ventilation pressure, the operating points of main fans may drift (relative to roadway structure), but the operating points recover with the discharge of gas. It is worth noting that the detention time of gas in low air quantity roadways and underground chambers is relatively long, and the gas becomes continuous gas supply sources, so it is dangerous. In addition, the delayed pour between main roadways and by-pass low air quantity roadways and the gas natural ventilation pressure caused by gas detention may lead to airflow disorder of reversion in some local circuits, and may enlarge the affected range of gas, or lead to the delay and detention of gas discharge.
    19  Addition of citric acid to enhance the bioleaching chalcopyrite tailings
    LI Dongwei LIANG Zhirong JIAO Binquan LI Dou
    2012, 35(11):117-121. DOI: 10.11835/j.issn.1000-582X.2012.11.019
    [Abstract](2067) [HTML](0) [PDF 6.81 M](1177)
    Abstract:
    The effect of mixed sulphur bacilli on the bioleaching of chalcopyrite tailings in shake flask and the effect of different citric acid concentrations and slurry densities on leaching tailings are studied. The results show that the concentration of citric acid in a certain range can promote chalcopyrite tailings bioleaching, and the highest of leaching rate is 44.8%. The citric acid concentration and slurry density directly affect the oxidation activity of bacteria and the effect of leaching.
    20  Numerical simulation of one-dimensional dam-break: A decoupled scheme with WENO reconstruction
    ZHANG Wenzhong CHEN Jingqiu ZHANG Yongxiang MIU Jilun
    2012, 35(11):122-125. DOI: 10.11835/j.issn.1000-582X.2012.11.020
    [Abstract](1795) [HTML](0) [PDF 4.22 M](1294)
    Abstract:
    Based on the reconstruction of interface variables with the fifth-order WENO, a high resolution scheme is proposed and the performance of capturing dam break waves is analyzed. With the part is linearized through Roe average, one dimensional shallow water equation is directly and decoupled solved, the velocity distribution and depth distribution are obtained. Numerical simulation shows that the decoupled schemes with WENO5 reconstruction has higher resolution and it shows the movement of dam-break.
    21  Calculation of broken index of surface based on GIS
    JIA Xingli XU Jingliang YANG Hongzhi ZHAO Liping
    2012, 35(11):126-130. DOI: 10.11835/j.issn.1000-582X.2012.11.021
    [Abstract](2952) [HTML](0) [PDF 7.42 M](1435)
    Abstract:
    Three factors, i.e. surface amplitude, incision density and incision depth are used to quantify the broken index of surface in order to study broken degree of surface. Based on the DEM, the calculation and extraction of single elements are finished by using GIS. Based on fuzzy clustering and rough set theory,a method is put forward to determine the influence coefficients of single elements in the composite element, and the formula of composite elements-the broken index of surface is elaboratcd to finish the calculation in Shandong Province. The calculation results indicate that a highly spatial heterogeneity exists in the broken index of surface in Shandong Province and it objectively shows the distribution of the broken degree of surface in Shandong Province and provide a basis for the zoning of highway and land division.
    22  Application of stepwise regression-time series and RBF-ANN models to precipitation forecasting
    LU Wenxi YANG Leilei YANG Zhongping XIN Xin LUO Jiannan CHU Haibo
    2012, 35(11):131-135. DOI: 10.11835/j.issn.1000-582X.2012.11.022
    [Abstract](2216) [HTML](0) [PDF 5.00 M](1186)
    Abstract:
    With integration of stepwise regression into the foundation of time series analysis model, the traditional mode of “take into account all the variables” is abandoned and just significant variables are used to establish the prediction equation in the form of “both enter and exit” mode, with the distinction of each factor’s major and minor relationship. The radial basis function artificial neural network (RBF-ANN) belongs to partial approaches network and has high accuracy. Take Huadian County’s month precipitation as an example, and compare the accuracy of prediction equations which are established using traditional, stepwise regression time series analysis model and RBF-ANN. The results show that the posterior error ratios of the traditional time series, stepwise regression time series and RBF-ANN models are 0.315, 0.272 and 0.284, the average absolute errors are 18.37 mm, 15.65 mm and 13.82 mm, and the effective coefficients are 0.87, 0.94 and 0.93. At last, we forecast the precipitation and evaporation in future three years with the stepwise regression time series analysis model.
    23  The distribution characteristics and evaluation of ecological risk of heavy metals in the surface sediment of Taihu Lake
    WANG Peifang ZHOU Wenming WANG Chao QIAN Jin HOU Jun ZHENG Shasha
    2012, 35(11):136-143. DOI: 10.11835/j.issn.1000-582X.2012.11.023
    [Abstract](2212) [HTML](0) [PDF 9.56 M](1152)
    Abstract:
    Research on the contents of heavy metals, such as Cd, Pb, Cu, Cr and their distribution characteristics in the surface sediments of 29 sampling sites in Taihu Lake, are conducted. Meanwhile, the distribution characters of the specific chemical forms of these heavy metals are analyzed with the method of BCR. Results show that the content of Cr has the highest values, while Cd has the lowest values, and contents of the four metals are different in different parts of Taihu Lake. The content of Cu and Cr in Meiliang Bay, Zhushan Bay and Gonghu Bay is high;while, the content of Cu in southern coast of the lake is the lowest;and the middle lake has the lowest content of Cr. Among the specific chemical forms of these heavy metals, the proportion of the extractable form of Cd is the highest, and Pb, Cu and Cr mainly exist in the residual form. This suggests Cd has the highest mobility among the four kinds of heavy metals. Furthermore, the potential ecological risk of these four kinds of heavy metals is evaluated by using the ratio of minor phase and progenetic phase(RSP). It shows that Pb, Cu and Cr are at pollution-free level in all parts of the lake. However, Cd is at moderate-polluted level in the sampling sites of river inlets of Zhushang Bay and western coastal lake, and at light-polluted level in parts of sites of Eastern Taihu Lake, Xuhu Bay, and Gonghu Bay. It indicates that Cd is the more serious pollutant in the whole lake of Taihu. And the descending order of the potential ecological risks of these heavy metals is Cd>Pb>Cu>Cr. Meanwhile, in terms of the different parts of the lake, southern coastal, middle lake and Gonghu Bay are at non-polluted level, and the others are at light-polluted level. However, the pollution level of Gonghu Bay is close to light-polluted level.
    24  Physical simulation of production performance of fractured horizontal wells in low permeability reservoir
    SHEN Rui GAO Shusheng XIONG Wei HU Zhiming
    2012, 35(11):144-148. DOI: 10.11835/j.issn.1000-582X.2012.11.024
    [Abstract](1678) [HTML](0) [PDF 5.76 M](1272)
    Abstract:
    For the fractured horizontal wells with spindle and dumbbell-shaped distribution of fracture in the Changqing oil-field, 3-D scaled physical models are utilized to simulate their production performance in elastic drive and waterflooding. The experimental results indicate that the oil production and the experimental time of two models are closely exponential function. The oil production of the horizontal well with dumbbell-shaped fracture is higher, but its decline rate is faster. The productivity formula and material balance equation of closed reservoir with elastic drive are utilized to derive the exponential form of oil production. Influence factors of oil production and its decline rate are analyzed in elastic drive. In waterflooding, the water breakthrough time of the horizontal well with spindle fracture is later than the one with dumbbell-shaped fracture. And the rate of water cut increasing of the model with spindle fracture is slower. In the initial stage of waterflooding experiment, elastic drive is still the leading position, so the oil production of the model with dumbbell-shaped fracture is higher. When the cumulative water injected exceeds 0.2 PV, the recovery percent of the model with spindle fracture is higher than the one of the model with dumbbell-shaped fracture. When the percent water cut reaches 98%, the recovery percent of the model with spindle fracture is 33.67%, while the one of the model with dumbbell-shaped fracture is 27.48%.

    Current Issue


    Volume , No.

    Table of Contents

    Archive

    Volume

    Issue

    Most Read

    Most Cited

    Most Downloaded